Forum Replies Created
-
AuthorPosts
-
dagakshayParticipant
hi Maneesh,
refer her for AVR inbuilt ADC
http://www.engineersgarage.com/embedded/avr-microcontroller-projects/adc-circuit
to display no on LCD
http://www.engineersgarage.com/microcontroller/8051projects/display-number-LCD-AT89C51-circuit
dagakshayParticipanthi nikhil…
do elobarte your problem… where exactly you got struct???
dagakshayParticipanthi ranjan its a simple Board you donot need any other interface for that… you can use AVRstuido
http://www.engineersgarage.com/tutorials/avr-studio4-working
refer here for more AVR tutorials
http://www.engineersgarage.com/embedded/avr-microcontroller-projects
July 23, 2011 at 5:58 am in reply to: How to interface Stepper motor and Dc motore with atmega16? #6499dagakshayParticipantuse Servo motors for the pick and place machnisum.
http://www.engineersgarage.com/embedded/avr-microcontroller-projects/atmega16-servo-motor-circuit
dagakshayParticipanthi sushant,
cna you explain you project… wht exactly you wanted to do with pendrive….,
dagakshayParticipantfor PIC trutorial refer to the link
http://www.engineersgarage.com/embedded/pic-microcontroller-projects
for GPS
http://www.engineersgarage.com/embedded/avr-microcontroller-projects/gps-interface-circuit
for soil moisture mesurement use two paralel pates dig them into soil and use ADC to calculate the amount of water level in the soil…….
dagakshayParticipantyou have to built an desktop application which can interact through PC and any of its peripherial… and write the code of your controller so that it can interact with that peripheral….
dagakshayParticipanthi tajdar,
here i am send you some links. these are from a very basic level.
http://www.engineersgarage.com/articles/avr-microcontroller
http://www.engineersgarage.com/tutorials/avr-studio4-working
http://www.engineersgarage.com/embedded/avr-microcontroller-projects
go through them and let me know if any help is required….
dagakshayParticipanthello Pradip,
the codes and ckts are very proper…. if still that code is not working remove the pullup resistors from the input pins on the keypad… then try let me know it you get if you get it….
dagakshayParticipantdagakshayParticipanthello Ahsan,
you can get C code on this site for reffering corresponding ASM code refer to the link.
http://www.engineersgarage.com/forums/8051/c-code-assembly-code
July 21, 2011 at 2:20 pm in reply to: how to start timer by software and stop by external hardware and then taking resultant value of time? #6482dagakshayParticipanthi zobi
try this it migh work out
mov TL0,<decimal value>
no need of pond”#” sign or to right ‘h’ at the end….
note: max value can go to 255 since TL0 is a 8 bit register
just let me know if it works???
dagakshayParticipanthi anish
have a look at these links it migh be helpfull for you
http://www.engineersgarage.com/embedded/avr-microcontroller-projects/gps-interface-circuit
http://www.engineersgarage.com/articles/gsm-gprs-modules
http://www.engineersgarage.com/forums/8051/how-interface-cellphone-micro-controller
July 21, 2011 at 2:02 pm in reply to: can i use seven segment display instead of Lcd for the project of distance measurment??? #6480dagakshayParticipantofcourse soban you can,
but better to use LCD since it will look more fanaticing and also reduces the ckt and code complexitiy if you using four digits to for display..
-
AuthorPosts