This Code is not working on MPLAB can anyone help me

[AHMAD JAVED]

//Program to interface GSM Modem with PIC18F4550 Microcontroller
//This code takes four choices as four inputs
//Choice 1 : Test the simple AT Command.
//Choice 2 : Find out the IMEI number of the GSM Modem.
//Choice 3 : Connect a call to a GSM mobile number.
//Choice 4 : Send a text message to a mobile number.

#define FREQ 12000000
#define baud 9600
#define spbrg_value (((FREQ/64)/baud)-1)
#define rs LATA.F0
#define rw LATA.F1
#define en LATA.F2
#define lcdport LATB

void tx_data(unsigned char);
unsigned char rx_data();
void lcd_ini();
void lcdcmd(unsigned char);
void lcddata(unsigned char);
void gsm_cmd(unsigned char *);
void output(void);

unsigned char value=0;
int i=0,j,k,temp,flag,choice;
unsigned char *starting_text=”Enter choice=”;
unsigned char *dial_text=”Dialing…”;
unsigned char *at_cmd=”AT”;
unsigned char *imei_cmd=”AT+GSN”;
unsigned char *call_cmd=”ATD9xxxxxxxxx;”; // Provide a 10-Digit Mobile Number
unsigned char *sms_format=”AT+CMGF=1″;
unsigned char *sms_write=”AT+CMGS=”xxxxxxxxxx””; // 10-Digit Mobile Number
unsigned char *sms=”Hello”;
unsigned char *sms_report=”SMS Sent…”;
unsigned char sms_terminate=0x1A;
unsigned char enter=0x0D;
unsigned char *data;

void main()
{
TRISB=0; // Set Port B as output port
LATB=0;
TRISA=0;
LATA=0;
TRISD=0xFF;
LATD=0;
SPBRG=spbrg_value; // Fill SPBRG register to set the baud rate
RCSTA.SPEN=1; // To activate serial port (Tx and Rx pins)
TXSTA.TXEN=1; // Activate Transmissiom
RCSTA.CREN=1; // Activate Reception
PIE1.RCIE=1; // Enable Reception interrupt
INTCON.GIE=1; // Enable Global interrupt
INTCON.PEIE=1; // Enable Peripheral interrupt

lcd_ini();
while(1)
{
k=0;
lcdcmd(0x80);
while(starting_text[k]!=’’)
{
lcddata(starting_text[k]);
k++;
}

//Check inputs

//Choice 1
if(PORTD.F0)
{
gsm_cmd(at_cmd);
output();
Delay_ms(1000);
}

//Choice 2
if(PORTD.F1)
{
gsm_cmd(imei_cmd);
output();
Delay_ms(1000);
}

//Choice 3
if(PORTD.F2)
{
gsm_cmd(call_cmd);
output();
Delay_ms(1000);
}

//Choice 4
if(PORTD.F3)
{
gsm_cmd(sms_format);
output();
Delay_ms(1000);

gsm_cmd(sms_write);
output();
Delay_ms(1000);

gsm_cmd(sms);
output();
tx_data(0x1A);
Delay_ms(1000);
}

}

}

void gsm_cmd(unsigned char *string)
{
i=0;j=0;
while(string!=’’)
{
temp=0;
if(string==0x5C) // Not to send ” cahracter
i++;
tx_data(string); // Send by serial communication
i++;
while(temp!=1);
}
temp=0;
tx_data(enter); // Send ASCII code for ‘Enter’ key
while(temp!=1);
}

void output(void) // To print data on LCD
{
lcdcmd(0x01);
i=-1;flag=0;
while(i {
if(flag>1)
{
flag=0;
Delay_ms(500);
lcdcmd(0x01);
lcdcmd(0x80);
}
if(data==0x0A) // This condition is to avoid double Enter

// during execution of a command
{
flag++;
lcdcmd(0xc0);
}
if(data==’>’||data=='”‘) // Not to print this character
{
i++;
lcdcmd(0xc0);
}
if(data!=0x0D&&data!=0x0A&&data!=0x1A) // Condition to print the data
// except ‘Enter’,’New line’ and ‘Submit’

{
lcddata(data);
i++;
}
else
i++;
Delay_ms(300);
}
lcdcmd(0x01);
}

void tx_data(unsigned char serial_data) // Transmit data function
{
TXREG=serial_data;
while(PIR1.TXIF==0);
}

void interrupt()
{
data[j]=RCREG; // Store the data into array when Reception interrupt occurs
value=RCREG;
j++;
temp=1;
}

void lcd_ini()
{
lcdcmd(0x38); // Configure the LCD in 8-bit mode, 2 line and 5×7 font
lcdcmd(0x0C); // Display On and Cursor Off
lcdcmd(0x01); // Clear display screen
lcdcmd(0x06); // Increment cursor
lcdcmd(0x80); // Set cursor position to 1st line, 1st column
}

void lcdcmd(unsigned char cmdout)
{
lcdport=cmdout; //Send command to lcdport=PORTB
rs=0;
rw=0;
en=1;
Delay_ms(10);
en=0;
}

void lcddata(unsigned char dataout)
{
lcdport=dataout; //Send data to lcdport=PORTB
rs=1;
rw=0;
en=1;
Delay_ms(10);
en=0;
}

[Author]

Posts