EngineersGarage

  • Engineers Garage Main Site
  • Visit our active EE Forums
    • EDABoard.com
    • Electro-Tech-Online
  • Projects & Tutorials
    • Circuits
    • Electronic Projects
    • Tutorials
    • Components
  • Digi-Key Store
    • Cables, Wires
    • Connectors, Interconnect
    • Discrete
    • Electromechanical
    • Embedded Computers
    • Enclosures, Hardware, Office
    • Integrated Circuits (ICs)
    • Isolators
    • LED/Optoelectronics
    • Passive
    • Power, Circuit Protection
    • Programmers
    • RF, Wireless
    • Semiconductors
    • Sensors, Transducers
    • Test Products
    • Tools
  • Advertise
You are here: Home / Topics / how to remove the flash magic error

how to remove the flash magic error

|

Microcontroller › 8051 › how to remove the flash magic error

  • This topic has 0 replies, 1 voice, and was last updated 14 years, 4 months ago by dagakshay.
Viewing 1 post (of 1 total)
  • Author
    Posts
  • February 24, 2011 at 5:10 am #4729
    dagakshay
    Participant

    many a times i get the query about flash magic that

    “It alway shows an error-“check all  hardware connection or baud rate not matched”.

    and on the other hand you have checked each and every hardware connection more than twice, your baud rate is 9600 and the com port u have selected is the same on which you have connected you burner…

     

    then what is the error how to come out of it… 

    am i right… 

    here is the mistake what we generally do since we are not aware of it.. we never configure the hardware.. here i am writing the steps just go through them.. and try to burn you controller then…

    step 1:

    go to option->advance options

     

    step 2:

    just uncheck the option marked in red in the figure below… since you are using only two pins Tx and Rx of your

    serial port to burn your controller…..

     

     

    now burn your ic and let me know if you have any problem…

  • Author
    Posts
Viewing 1 post (of 1 total)
  • You must be logged in to reply to this topic.
Log In

RSS Recent Posts

  • Display TFT ST7789 (OshonSoft Basic). July 10, 2025
  • Fixing board, Easy question HEX SCHMITT July 10, 2025
  • Can I make two inputs from one?? July 10, 2025
  • Home Smoke detectors are all Beeping Batteries are not dead.??? July 9, 2025
  • The Analog Gods Hate Me July 9, 2025

Stay Up To Date

Newsletter Signup
EngineersGarage

Copyright © 2025 WTWH Media LLC. All Rights Reserved. The material on this site may not be reproduced, distributed, transmitted, cached or otherwise used, except with the prior written permission of WTWH Media
Privacy Policy | Advertising | About Us

Search Engineers Garage

  • Engineers Garage Main Site
  • Visit our active EE Forums
    • EDABoard.com
    • Electro-Tech-Online
  • Projects & Tutorials
    • Circuits
    • Electronic Projects
    • Tutorials
    • Components
  • Digi-Key Store
    • Cables, Wires
    • Connectors, Interconnect
    • Discrete
    • Electromechanical
    • Embedded Computers
    • Enclosures, Hardware, Office
    • Integrated Circuits (ICs)
    • Isolators
    • LED/Optoelectronics
    • Passive
    • Power, Circuit Protection
    • Programmers
    • RF, Wireless
    • Semiconductors
    • Sensors, Transducers
    • Test Products
    • Tools
  • Advertise