we are using arduino uno and

[Hemali]

we are using arduino uno and fingerprint sensor 1125.

 

our code is as follows….the underlined part is always coming as an output….any idea whats wrong withg this code?

 

 

 

 

 

#include <Adafruit_Fingerprint.h>
#if ARDUINO >= 100
 #include <SoftwareSerial.h>
#else
 #include <NewSoftSerial.h>
#endif

uint8_t getFingerprintEnroll(uint8_t id);

// pin #2 is IN from sensor (GREEN wire)
// pin #3 is OUT from arduino  (WHITE wire)
#if ARDUINO >= 100
SoftwareSerial mySerial(2, 3);
#else
NewSoftSerial mySerial(2, 3);
#endif

Adafruit_Fingerprint finger = Adafruit_Fingerprint(&mySerial);

void setup() 
{
  Serial.begin(9600);
  Serial.println(“fingertest”);

  // set the data rate for the sensor serial port
  finger.begin(57600);
 
  if (finger.verifyPassword()) {
    Serial.println(“Found fingerprint sensor!”);
  } else {
    Serial.println(“Did not find fingerprint sensor “);
    while (1);
  }
}

void loop()                     // run over and over again
{
  Serial.println(“Type in the ID # you want to save this finger as…”);
  uint8_t id = 0;
  while (true) {
    while (! Serial.available());
    char c = Serial.read();
    if (! isdigit(c)) break;
    id *= 10;
    id += c – ‘0’;
  }
  Serial.print(“Enrolling ID #”);
  Serial.println(id);
 
  while (!  getFingerprintEnroll(id) );
}

uint8_t getFingerprintEnroll(uint8_t id) {
  uint8_t p = -1;
  Serial.println(“Waiting for valid finger to enroll”);
  while (p != FINGERPRINT_OK) {
    p = finger.getImage();
    switch (p) {
    case FINGERPRINT_OK:
      Serial.println(“Image taken”);
      break;
    case FINGERPRINT_NOFINGER:
      Serial.println(“.”);
      break;
    case FINGERPRINT_PACKETRECIEVEERR:
      Serial.println(“Communication error”);
      break;
    case FINGERPRINT_IMAGEFAIL:
      Serial.println(“Imaging error”);
      break;
    default:
      Serial.println(“Unknown error”);
      break;
    }
  }

  // OK success!

  p = finger.image2Tz(1);
  switch (p) {
    case FINGERPRINT_OK:
      Serial.println(“Image converted”);
      break;
    case FINGERPRINT_IMAGEMESS:
      Serial.println(“Image too messy”);
      return p;
    case FINGERPRINT_PACKETRECIEVEERR:
      Serial.println(“Communication error”);
      return p;
    case FINGERPRINT_FEATUREFAIL:
      Serial.println(“Could not find fingerprint features”);
      return p;
    case FINGERPRINT_INVALIDIMAGE:
      Serial.println(“Could not find fingerprint features”);
      return p;
    default:
      Serial.println(“Unknown error”);
      return p;
  }
 
  Serial.println(“Remove finger”);
  delay(2000);
  p = 0;
  while (p != FINGERPRINT_NOFINGER) {
    p = finger.getImage();
  }

  p = -1;
  Serial.println(“Place same finger again”);
  while (p != FINGERPRINT_OK) {
    p = finger.getImage();
    switch (p) {
    case FINGERPRINT_OK:
      Serial.println(“Image taken”);
      break;
    case FINGERPRINT_NOFINGER:
      Serial.print(“.”);
      break;
    case FINGERPRINT_PACKETRECIEVEERR:
      Serial.println(“Communication error”);
      break;
    case FINGERPRINT_IMAGEFAIL:
      Serial.println(“Imaging error”);
      break;
    default:
      Serial.println(“Unknown error”);
      break;
    }
  }

  // OK success!

  p = finger.image2Tz(2);
  switch (p) {
    case FINGERPRINT_OK:
      Serial.println(“Image converted”);
      break;
    case FINGERPRINT_IMAGEMESS:
      Serial.println(“Image too messy”);
      return p;
    case FINGERPRINT_PACKETRECIEVEERR:
      Serial.println(“Communication error”);
      return p;
    case FINGERPRINT_FEATUREFAIL:
      Serial.println(“Could not find fingerprint features”);
      return p;
    case FINGERPRINT_INVALIDIMAGE:
      Serial.println(“Could not find fingerprint features”);
      return p;
    default:
      Serial.println(“Unknown error”);
      return p;
  }
 
 
  // OK converted!
  p = finger.createModel();
  if (p == FINGERPRINT_OK) {
    Serial.println(“Prints matched!”);
  } else if (p == FINGERPRINT_PACKETRECIEVEERR) {
    Serial.println(“Communication error”);
    return p;
  } else if (p == FINGERPRINT_ENROLLMISMATCH) {
    Serial.println(“Fingerprints did not match”);
    return p;
  } else {
    Serial.println(“Unknown error”);
    return p;
  }  
 
  p = finger.storeModel(id);
  if (p == FINGERPRINT_OK) {
    Serial.println(“Stored!”);
  } else if (p == FINGERPRINT_PACKETRECIEVEERR) {
    Serial.println(“Communication error”);
    return p;
  } else if (p == FINGERPRINT_BADLOCATION) {
    Serial.println(“Could not store in that location”);
    return p;
  } else if (p == FINGERPRINT_FLASHERR) {
    Serial.println(“Error writing to flash”);
    return p;
  } else {
    Serial.println(“Unknown error”);
    return p;
  }  
}